Container Networking: Part Three

This is the third part of the series Container Networking. I will explain little bit of docker container networking in this blog post.

I followed steps mentioned at this to install docker on Ubuntu.

Post docker install, you can see docker0 device in the list

$ ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp0s3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
    link/ether 02:fd:4d:34:55:76 brd ff:ff:ff:ff:ff:ff
11: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default 
    link/ether 02:42:cf:b4:c1:a8 brd ff:ff:ff:ff:ff:ff

Let’s create a busybox container

$ docker run --name bb -dt busybox

$ docker ps -a
CONTAINER ID   IMAGE     COMMAND   CREATED              STATUS              PORTS    NAMES
02429964e449   busybox   "sh"      About a minute ago   Up About a minute             bb

In device list, you see veth7b01920@if16 interface is created with master as docker0

$ ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp0s3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
    link/ether 02:fd:4d:34:55:76 brd ff:ff:ff:ff:ff:ff
11: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default 
    link/ether 02:42:cf:b4:c1:a8 brd ff:ff:ff:ff:ff:ff
17: veth7b01920@if16: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master docker0 state UP mode DEFAULT group default 
    link/ether e2:15:50:88:11:03 brd ff:ff:ff:ff:ff:ff link-netnsid 2

Let’s check the network namespace

$ ip netns list

And you won’t see any network namespaces…How come??? This is because

ip netns list command looks up network namespaces file in the 
/var/run/netns directory.

However, the Docker daemon doesn’t create a reference of
the network namespace file in the /var/run/netns directory
after the creation. Therefore, ip netns ls cannot resolve the
network namespace file

Ref: https://www.baeldung.com/linux/docker-network-namespace-invisible

If you want ip netns list should show the namespace name docker has created, then follow below steps

export container_name=bb
container_pid=$(sudo docker inspect -f '' $container_name)
echo $container_pid

sudo touch /var/run/netns/$container_name
sudo mount -o bind /proc/$container_pid/ns/net /var/run/netns/$container_name

Now you can see the namespace name

$ ip netns list
bb (id: 0)

sudo ip netns exec bb ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
16: eth0@if17: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default 
    link/ether 02:42:ac:11:00:02 brd ff:ff:ff:ff:ff:ff link-netnsid 0

Following diagram will help you to visualize better.

With this, signing off. I hope this blog series helps to de-clutter the container networking.